Diffusion Instrument Control (confint-fix) Browse

MyZiRingdown.m
d1ba8061982aconfint-fix

MyZiRingdown.m
View Options

			% Class for performing ringdown measurements of mechanical oscillators
			% using Zurich Instruments UHF or MF lock-in.
			%
			% Operation: sweep the driving tone (drive_osc) using the sweep module
			% in LabOne web user interface, when the magnitude of the demodulator
			% signal exceeds trig_threshold the driving tone is switched off and
			% the recording of demodulated signal is started, the signal is recorded
			% for the duration of record_time.
			%
			% Features:
			%
			% Adaptive measurement oscillator frequency
			%
			% Averaging
			%
			% Auto saving
			%
			% Auxiliary output signal: If enable_aux_out=true
			% then after a ringdown is started a sequence of pulses is applied
			% to the output consisting of itermittent on and off periods
			% starting from on.

			classdef MyZiRingdown < MyZiLockIn & MyDataSource

			properties (Access = public, SetObservable = true)

			% Ringdown is recorded if the signal in the triggering demodulation
			% channel exceeds this value
			trig_threshold = 1e-3 % V

			% Duration of the recorded ringdown
			record_time = 1 % (s)

			% If enable_acq is true, then the drive is on and the acquisition
			% of record is triggered when signal exceeds trig_threshold
			enable_acq = false

			% Auxiliary output signal during ringdown.
			enable_aux_out = false % If auxiliary output is applied

			% time during which the output is in aux_out_on_lev state
			aux_out_on_t = 1 % (s)

			% time during which the output is in aux_out_off_lev state
			aux_out_off_t = 1 % (s)

			aux_out_on_lev = 1 % (V), output trigger on level
			aux_out_off_lev = 0 % (V), output trigger off level

			% Average the trace over n points to reduce amount of stored data
			% while keeping the demodulator bandwidth large
			downsample_n = 1

			fft_length = 128

			auto_save = false % if all ringdowns should be automatically saved

			% In adaptive measurement oscillator mode the oscillator frequency
			% is continuously changed to follow the signal frequency during
			% ringdown acquisition. This helps against the oscillator frequency
			% drift.
			adaptive_meas_osc = false
			end

			% The properties which are read or set only once during the class
			% initialization
			properties (GetAccess = public, SetAccess = {?MyClassParser}, ...
			SetObservable = true)

			% enumeration for demodulators, oscillators and output starts from 1
			demod = 1 % demodulator used for both triggering and measurement

			% Enumeration in the node structure starts from 0, so, for example,
			% the default path to the trigger demodulator refers to the
			% demodulator #1
			demod_path = '/dev4090/demods/0'

			drive_osc = 1
			meas_osc = 2

			% Signal input, integers above 1 correspond to main inputs, aux
			% input etc. (see the user interface for device-specific details)
			signal_in = 1

			drive_out = 1 % signal output used for driving

			% Number of an auxiliary channel used for the output of triggering
			% signal, primarily intended to switch the measurement apparatus
			% off during a part of the ringdown and thus allow for free
			% evolution of the oscillator during that period.
			aux_out = 1

			% Poll duration of 1 ms practically means that ziDAQ('poll', ...
			% returns immediately with the data accumulated since the
			% previous function call.
			poll_duration = 0.001 % s
			poll_timeout = 50 % ms

			% Margin for adaptive oscillator frequency adjustment - oscillator
			% follows the signal if the dispersion of frequency in the
			% demodulator band is below ad_osc_margin times the demodulation
			% bandwidth (under the condition that adaptive_meas_osc=true)
			ad_osc_margin = 0.1
			end

			% Internal variables
			properties (GetAccess = public, SetAccess = protected, ...
			SetObservable = true)

			recording = false % true if a ringdown is being recorded

			% true if adaptive measurement oscillator mode is on and if the
			% measurement oscillator is actually actively following.
			ad_osc_following = false

			% Reference timestamp at the beginning of measurement record.
			% Stored as uint64.
			t0

			elapsed_t = 0 % Time elapsed since the last recording was started

			DemodSpectrum % MyTrace object to store FFT of the demodulator data
			end

			% Other dependent variables that are not device properties
			properties (Dependent = true, SetObservable = true)

			% Downsample the measurement record to reduce the amount of data
			% while keeping the large demodulation bandwidth.
			% (samples/s), sampling rate of the trace after avraging
			downsampled_rate

			% Provides public access to properties of private AvgTrace
			n_avg % number of ringdowns to be averaged
			avg_count % the average counter

			fft_rbw % resolution bandwidth of fft

			poll_period % (s)
			end

			% Keeping handle objects fully private is the only way to restrict set
			% access to their properties
			properties (Access = private)
			PollTimer

			AuxOutOffTimer % Timer responsible for switching the aux out off
			AuxOutOnTimer % Timer responsible for switching the aux out on

			% Demodulator samples z(t) stored to continuously calculate
			% spectrum, the values of z are complex here, z=x+iy.
			% osc_freq is the demodulation frequency
			DemodRecord = struct('t',[],'z',[],'osc_freq',[])

			AvgTrace % MyAvgTrace object used for averaging ringdowns
			end

			events
			NewDemodSample % New demodulator samples received
			RecordingStarted % Acquisition of a new trace triggered
			end

			methods (Access = public)

			%% Constructor and destructor
			function this = MyZiRingdown(varargin)

			% Extract poll period from varargin
			p = inputParser();
			p.KeepUnmatched = true;
			addParameter(p, 'poll_period', 0.042, @isnumeric);
			parse(p, varargin{:});
			varargin = struct2namevalue(p.Unmatched);

			this = this@MyZiLockIn(varargin{:});

			% Create and configure trace objects
			% Trace is inherited from the superclass
			this.Trace = MyTrace(...
			'name_x','Time',...
			'unit_x','s',...
			'name_y','Magnitude r',...
			'unit_y','V');

			this.DemodSpectrum = MyTrace(...
			'name_x','Frequency',...
			'unit_x','Hz',...
			'name_y','PSD',...
			'unit_y','V^2/Hz');

			this.AvgTrace = MyAvgTrace();

			% Set up the poll timer. Using a timer for anyncronous
			% data readout allows to use the wait time for execution
			% of other programs.
			% Fixed spacing is preferred as it is the most robust mode of
			% operation when keeping the intervals between callbacks
			% precisely defined is not the biggest concern.
			this.PollTimer = timer(...
			'ExecutionMode', 'fixedSpacing',...
			'Period', p.Results.poll_period,...
			'TimerFcn', @this.pollTimerCallback);

			% Aux out timers use fixedRate mode for more precise timing.
			% The two timers are executed periodically with a time lag.
			% The first timer switches the auxiliary output off
			this.AuxOutOffTimer = timer(...
			'ExecutionMode', 'fixedRate',...
			'TimerFcn', @this.auxOutOffTimerCallback);

			% The second timer switches the auxiliary output on
			this.AuxOutOnTimer = timer(...
			'ExecutionMode', 'fixedRate',...
			'TimerFcn', @this.auxOutOnTimerCallback);

			this.demod_path = sprintf('/%s/demods/%i', this.dev_id, ...
			this.demod-1);
			end

			function delete(this)

			% delete function should never throw errors, so protect
			% statements with try-catch
			try
			stopPoll(this)
			catch
			warning(['Could not usubscribe from the demodulator ', ...
			'or stop the poll timer.'])
			end

			% Delete timers to prevent them from running indefinitely in
			% the case of program crash
			try
			delete(this.PollTimer)
			catch
			warning('Could not delete the poll timer.')
			end

			try
			stop(this.AuxOutOffTimer);
			delete(this.AuxOutOffTimer);
			catch
			warning('Could not stop and delete AuxOutOff timer.')
			end

			try
			stop(this.AuxOutOnTimer);
			delete(this.AuxOutOnTimer);
			catch
			warning('Could not stop and delete AuxOutOn timer.')
			end
			end

			%% Other methods

			function startPoll(this)

			% Configure the oscillators, demodulator and driving output
			% -1 accounts for the difference in enumeration conventions
			% in the software names (starting from 1) and node numbers
			% (starting from 0).
			% First, update the demodulator path
			this.demod_path = sprintf('/%s/demods/%i', ...
			this.dev_id, this.demod-1);

			% Set the data transfer rate so that it satisfies the Nyquist
			% criterion (>x2 the bandwidth of interest)
			this.demod_rate = 4*this.lowpass_bw;

			% Configure the demodulator. Signal input:
			ziDAQ('setInt', ...
			[this.demod_path,'/adcselect'], this.signal_in-1);

			% Oscillator:
			ziDAQ('setInt', ...
			[this.demod_path,'/oscselect'], this.drive_osc-1);

			% Enable data transfer from the demodulator to the computer
			ziDAQ('setInt', [this.demod_path,'/enable'], 1);

			% Configure the signal output - disable all the oscillator
			% contributions excluding the driving tone
			path = sprintf('/%s/sigouts/%i/enables/*', ...
			this.dev_id, this.drive_out-1);
			ziDAQ('setInt', path, 0);

			path = sprintf('/%s/sigouts/%i/enables/%i', ...
			this.dev_id, this.drive_out-1, this.drive_osc-1);
			ziDAQ('setInt', path, 1);

			% Enable output
			this.drive_on = true;

			% By convention, we start form 'enable_acq=false' state
			this.enable_acq = false;

			% Configure the auxiliary trigger output - put it in the manual
			% mode so it does not output demodulator readings
			path = sprintf('/%s/auxouts/%i/outputselect', ...
			this.dev_id, this.aux_out-1);
			ziDAQ('setInt', path, -1);

			% The convention is that aux out is on by default
			this.aux_out_on = true;

			% Subscribe to continuously receive samples from the
			% demodulator. Samples accumulated between timer callbacks
			% will be read out using ziDAQ('poll', ...
			ziDAQ('subscribe', [this.demod_path,'/sample']);

			% Start continuous polling
			start(this.PollTimer)
			end

			function stopPoll(this)
			stop(this.PollTimer)
			ziDAQ('unsubscribe', [this.demod_path,'/sample']);
			end

			% Main function that polls data from the device demodulator
			function pollTimerCallback(this, ~, ~)

			% ziDAQ('poll', ... with short poll_duration returns
			% immediately with the data accumulated since the last timer
			% callback
			Data = ziDAQ('poll', this.poll_duration, this.poll_timeout);

			if ziCheckPathInData(Data, [this.demod_path, '/sample'])

			% Demodulator returns data
			DemodSample = ...
			Data.(this.dev_id).demods(this.demod).sample;

			% Append new samples to the record and recalculate spectrum
			appendSamplesToBuff(this, DemodSample);
			calcfft(this);

			if this.recording

			% If the recording has just started, save the start
			% time
			if isempty(this.Trace)
			this.t0 = DemodSample.timestamp(1);
			end

			% If recording is under way, append the new samples to
			% the trace
			rec_finished = appendSamplesToTrace(this, DemodSample);

			% Recording can be manually stopped by setting
			% enable_acq=false
			if ~this.enable_acq
			rec_finished = true;
			end

			% Update elapsed time
			this.elapsed_t = this.Trace.x(end);

			% If the adaptive measurement frequency mode is on,
			% update the measurement oscillator frequency.
			% Make sure that the demodulator record actually
			% contains a signal by comparing the dispersion of
			% frequency to the demodulator bandwidth.
			if this.adaptive_meas_osc
			[df_avg, df_dev] = calcfreq(this);
			if df_dev < this.ad_osc_margin*this.lowpass_bw
			this.meas_osc_freq = df_avg;

			% Change indicator
			this.ad_osc_following = true;
			else
			this.ad_osc_following = false;
			end
			else
			this.ad_osc_following = false;
			end
			else
			r = sqrt(DemodSample.x.^2+DemodSample.y.^2);
			if this.enable_acq && max(r)>this.trig_threshold

			% Start acquisition of a new trace if the maximum
			% of the signal exceeds threshold
			this.recording = true;
			this.elapsed_t = 0;

			% Switch the drive off
			this.drive_on = false;

			% Set the measurement oscillator frequency to be
			% the frequency at which triggering occurred
			this.meas_osc_freq = this.drive_osc_freq;

			% Switch the oscillator
			this.current_osc = this.meas_osc;

			% Clear the buffer on ZI data server from existing
			% demodulator samples, as these samples were
			% recorded with drive on
			ziDAQ('poll',this.poll_duration,this.poll_timeout);

			% Optionally start the auxiliary output timers
			if this.enable_aux_out

			% Configure measurement periods and delays
			T = this.aux_out_on_t + this.aux_out_off_t;
			this.AuxOutOffTimer.Period = T;
			this.AuxOutOnTimer.Period = T;

			this.AuxOutOffTimer.startDelay =...
			this.aux_out_on_t;
			this.AuxOutOnTimer.startDelay = T;

			% Start timers
			start(this.AuxOutOffTimer)
			start(this.AuxOutOnTimer)
			end

			% Clear trace
			clear(this.Trace);

			notify(this, 'RecordingStarted');
			end

			rec_finished = false;

			% Indicator for adaptive measurement is off, since
			% recording is not under way
			this.ad_osc_following = false;
			end

			notify(this,'NewDemodSample');

			% Stop recording if a record was completed
			if rec_finished

			% stop recording
			this.recording = false;
			this.ad_osc_following = false;

			% Stop auxiliary timers
			stop(this.AuxOutOffTimer);
			stop(this.AuxOutOnTimer);

			% Return the drive and aux out to the default state
			this.aux_out_on = true;
			this.current_osc = this.drive_osc;
			this.drive_on = true;

			% Downsample the trace to reduce the amount of data
			downsample(this.Trace, this.downsample_n, 'avg');

			% Do trace averaging. If the new data length is not of
			% the same size as the length of the existing data
			% (which should happen only when the record period was
			% changed during recording or when recording was
			% manually stopped), truncate to the minimum length
			if ~isempty(this.AvgTrace) && ...
			(length(this.AvgTrace.y)~=length(this.Trace.y))

			l = min(length(this.AvgTrace.y), ...
			length(this.Trace.y));

			this.AvgTrace.y = this.AvgTrace.y(1:l);
			this.AvgTrace.x = this.AvgTrace.x(1:l);
			this.Trace.y = this.Trace.y(1:l);
			this.Trace.x = this.Trace.x(1:l);

			disp('Ringdown record was truncated')
			end
			avg_compl = addAverage(this.AvgTrace, this.Trace);

			% Trigger NewData
			if this.n_avg>1
			end_str = sprintf('_%i', this.AvgTrace.avg_count);
			else
			end_str = '';
			end
			triggerNewData(this, 'save', this.auto_save, ...
			'filename_ending', end_str);

			% If the ringdown averaging is complete, disable
			% further triggering to exclude data overwriting
			if avg_compl
			this.enable_acq = false;

			if this.n_avg>1
			end_str = '_avg';

			% Trigger one more time to transfer the average
			% trace.
			% A new measurement header is not necessary
			% as the delay since the last triggering is
			% minimum.
			triggerNewData(this, ...
			'Trace', copy(this.AvgTrace), ...
			'save', this.auto_save, ...
			'filename_ending', end_str);
			end
			end
			end
			end
			end

			% Append timestamps vs r=sqrt(x^2+y^2) to the measurement record.
			% Starting index can be supplied as varargin.
			% The output variable tells if the record is finished.
			function isfin = appendSamplesToTrace(this, DemodSample)

			r = sqrt(DemodSample.x.^2 + DemodSample.y.^2);

			% Subtract the reference time, convert timestamps to seconds
			ts = double(DemodSample.timestamp - this.t0)/this.clockbase;

			% Check if recording should be stopped
			isfin = (ts(end)>=this.record_time);
			if isfin
			% Remove excess data points from the new data
			ind = (ts<this.record_time);
			ts = ts(ind);
			r = r(ind);
			end

			% Append the new data in column format to the trace
			this.Trace.x = [this.Trace.x; ts(:)];
			this.Trace.y = [this.Trace.y; r(:)];
			end

			% Append timestamps vs z=x+iy to the shift register for fft
			% calculation
			function appendSamplesToBuff(this, DemodSample)
			z = complex(DemodSample.x, DemodSample.y);
			t = double(DemodSample.timestamp)/this.clockbase;

			% Convert the new data to column format and append
			this.DemodRecord.t = [this.DemodRecord.t; t(:)];
			this.DemodRecord.z = [this.DemodRecord.z; z(:)];
			this.DemodRecord.osc_freq = [this.DemodRecord.osc_freq; ...
			DemodSample.frequency(:)];

			assert(length(this.DemodRecord.t) == ...
			length(this.DemodRecord.z), ...
			't and z=x+iy array lengths of DemodRecord are not equal.')

			% Only store the latest data points required to calculate fft
			flen = this.fft_length;
			if length(this.DemodRecord.t)>flen
			this.DemodRecord.t = this.DemodRecord.t(end-flen+1:end);
			this.DemodRecord.z = this.DemodRecord.z(end-flen+1:end);
			this.DemodRecord.osc_freq = ...
			this.DemodRecord.osc_freq(end-flen+1:end);
			end
			end

			function calcfft(this)
			flen = min(this.fft_length, length(this.DemodRecord.t));
			[freq, spectr] = xyFourier( ...
			this.DemodRecord.t(end-flen+1:end), ...
			this.DemodRecord.z(end-flen+1:end));
			this.DemodSpectrum.x = freq;
			this.DemodSpectrum.y = abs(spectr).^2;
			end

			% Calculate the average frequency and dispersion of the demodulator
			% signal
			function [f_avg, f_dev] = calcfreq(this)
			if ~isempty(this.DemodSpectrum)
			norm = sum(this.DemodSpectrum.y);

			% Calculate the center frequency of the spectrum
			f_avg=dot(this.DemodSpectrum.x, this.DemodSpectrum.y)/norm;

			f_dev=sqrt(dot(this.DemodSpectrum.x.^2, ...
			this.DemodSpectrum.y)/norm-f_avg^2);

			% Shift the FFT center by the demodulation frequency to
			% output absolute value
			f_avg = f_avg + mean(this.DemodRecord.osc_freq);
			else
			f_avg = [];
			f_dev = [];
			end
			end

			% Provide restricted access to private AvgTrace
			function resetAveraging(this)

			% Clear data and reset counter
			clear(this.AvgTrace);
			end

			function auxOutOffTimerCallback(this, ~, ~)
			this.aux_out_on = false;
			end

			function auxOutOnTimerCallback(this, ~, ~)
			this.aux_out_on = true;
			end
			end

			methods (Access = protected)
			function createCommandList(this)

			path = sprintf('/%s/oscs/%i/freq', this.dev_id, ...
			this.drive_osc-1);

			addCommand(this, 'drive_osc_freq', ...
			'readFcn', @()ziDAQ('getDouble', path), ...
			'writeFcn', @(x)ziDAQ('setDouble', path, x));

			path = sprintf('/%s/oscs/%i/freq', this.dev_id, ...
			this.meas_osc-1);

			addCommand(this, 'meas_osc_freq', ...
			'readFcn', @()ziDAQ('getDouble', path), ...
			'writeFcn', @(x)ziDAQ('setDouble', path, x));

			% Use double() to convert from logical type
			path = sprintf('/%s/sigouts/%i/on', this.dev_id, ...
			this.drive_out-1);

			addCommand(this, 'drive_on', ...
			'readFcn', @()logical(ziDAQ('getInt', path)), ...
			'writeFcn', @(x)ziDAQ('setInt', path, double(x)));

			addCommand(this, 'current_osc', ...
			'readFcn', @()(double(ziDAQ('getInt', ...
			[this.demod_path,'/oscselect']))+1), ...
			'writeFcn', @(x)ziDAQ('setInt', ...
			[this.demod_path,'/oscselect'], x-1));

			path = sprintf('/%s/sigouts/%i/amplitudes/%i', ...
			this.dev_id, this.drive_out-1, this.drive_osc-1);

			addCommand(this, 'drive_amp', ...
			'readFcn', @()ziDAQ('getDouble', path), ...
			'writeFcn', @(x)ziDAQ('setDouble', path, x));

			addCommand(this, 'lowpass_order', ...
			'readFcn', @()(double(ziDAQ('getInt', ...
			[this.demod_path,'/oscselect']))+1), ...
			'writeFcn', @(x)ziDAQ('setInt', ...
			[this.demod_path '/order'], x), ...
			'validationFcn', @(x)assert(any(x==[1,2,3,4,5,6,7,8]),...
			['Low-pass filter order must be an integer between '...
			'1 and 8']), ...
			'default', 1);

			addCommand(this, 'lowpass_bw', ...
			'readFcn', @()ziTC2BW(ziDAQ('getDouble', ...
			[this.demod_path,'/timeconstant'])), ...
			'writeFcn', @(x)ziDAQ('setDouble', ...
			[this.demod_path,'/timeconstant'], ziBW2TC(x)));

			addCommand(this, 'demod_rate', ...
			'readFcn', @()ziDAQ('getDouble', ...
			[this.demod_path,'/rate']), ...
			'writeFcn', @(x)ziDAQ('setDouble', ...
			[this.demod_path,'/rate'], x));

			% The auxiliary output level can be in one of two states, on or
			% off
			path = sprintf('/%s/auxouts/%i/offset', this.dev_id, ...
			this.aux_out-1);

			addCommand(this, 'aux_out_on', ...
			'readFcn', @()ziDAQ('getDouble', path), ...
			'postSetFcn', @(x) (abs(x-this.aux_out_on_lev) < ...
			abs(x-this.aux_out_off_lev)), ...
			'writeFcn', @(x)ziDAQ('setDouble', path, ...
			select(x, this.aux_out_on_lev, this.aux_out_off_lev)));
			end

			function createMetadata(this)
			createMetadata@MyZiLockIn(this);

			% Demodulator parameters
			addObjProp(this.Metadata, this, 'demod', 'comment', ...
			'Number of the demodulator in use (starting from 1)');
			addObjProp(this.Metadata, this, 'meas_osc', 'comment', ...
			'Measurement oscillator number');

			% Signal input
			addObjProp(this.Metadata, this, 'signal_in', 'comment', ...
			'Singnal input number');

			% Drive parameters
			addObjProp(this.Metadata, this, 'drive_out', 'comment', ...
			'Driving output number');
			addObjProp(this.Metadata, this, 'drive_osc', 'comment', ...
			'Swept oscillator number');

			% Parameters of the auxiliary output
			addObjProp(this.Metadata, this, 'aux_out', 'comment', ...
			'Auxiliary output number');
			addObjProp(this.Metadata, this, 'enable_aux_out', 'comment',...
			'Auxiliary output is applied during ringdown');
			addObjProp(this.Metadata, this, 'aux_out_on_lev', ...
			'comment', '(V)');
			addObjProp(this.Metadata, this, 'aux_out_off_lev', ...
			'comment', '(V)');
			addObjProp(this.Metadata, this, 'aux_out_on_t', ...
			'comment', '(s)');
			addObjProp(this.Metadata, this, 'aux_out_off_t', ...
			'comment', '(s)');

			% Software parameters
			addObjProp(this.Metadata, this, 'trig_threshold', 'comment',...
			'(V), threshold for starting a ringdown record');
			addObjProp(this.Metadata, this, 'record_time', ...
			'comment', '(s)');
			addObjProp(this.Metadata, this, 'downsampled_rate', ...
			'comment', ['(samples/s), rate to which a ringown ', ...
			'trace is downsampled with averaging after acquisition']);
			addObjProp(this.Metadata, this, 'auto_save', 'comment', '(s)');

			% Adaptive measurement oscillator
			addObjProp(this.Metadata, this, 'adaptive_meas_osc', ...
			'comment', ['If true the measurement oscillator ', ...
			'frequency is adjusted during ringdown']);
			addObjProp(this.Metadata, this, 'ad_osc_margin');
			addObjProp(this.Metadata, this, 'fft_length', ...
			'comment', '(points)');

			% Timer poll parameters
			addParam(this.Metadata, 'poll_period', [],...
			'comment', '(s)');
			addObjProp(this.Metadata, this, 'poll_duration', ...
			'comment', '(s)');
			addObjProp(this.Metadata, this, 'poll_timeout', ...
			'comment', '(ms)');
			end
			end

			%% Set and get methods.
			methods
			function set.downsample_n(this, val)
			n = round(val);
			assert(n>=1, ['Number of points for trace averaging must ', ...
			'be greater than 1'])
			this.downsample_n = n;
			end

			function set.downsampled_rate(this, val)
			dr = this.demod_rate;

			% Downsampled rate should not exceed the data transfer rate
			val = min(val, dr);

			% Round so that the averaging is done over an integer number of
			% points
			this.downsample_n = round(dr/val);
			end

			function val = get.downsampled_rate(this)
			val = this.demod_rate/this.downsample_n;
			end

			function set.fft_length(this, val)

			% Round val to the nearest 2^n to make the calculation of
			% Fourier transform efficient
			n = round(log2(max(val, 1)));
			this.fft_length = 2^n;
			end

			function val = get.fft_rbw(this)
			val = this.demod_rate/this.fft_length;
			end

			function set.fft_rbw(this, val)
			assert(val>0,'FFT resolution bandwidth must be greater than 0')
			% Rounding of fft_length to the nearest integer is handled by
			% its own set method

			this.fft_length = this.demod_rate/val;
			end

			function set.n_avg(this, val)
			this.AvgTrace.n_avg = val;
			end

			function val = get.n_avg(this)
			val = this.AvgTrace.n_avg;
			end

			function val = get.avg_count(this)
			val = this.AvgTrace.avg_count;
			end

			function set.aux_out_on_t(this, val)
			assert(val>0.001, ...
			'Aux out on time must be greater than 0.001 s.')
			this.aux_out_on_t = val;
			end

			function set.aux_out_off_t(this, val)
			assert(val>0.001, ...
			'Aux out off time must be greater than 0.001 s.')
			this.aux_out_off_t = val;
			end

			function set.enable_acq(this, val)
			this.enable_acq = logical(val);
			end

			function val = get.poll_period(this)
			val = this.PollTimer.Period;
			end
			end
			end

rINSTCONTROL/@MyZiRingdown/MyZiRingdown.md1ba8061982aconfint-fix

MyZiRingdown.mView Options

rINSTCONTROL/@MyZiRingdown/MyZiRingdown.m
d1ba8061982aconfint-fix

MyZiRingdown.m
View Options