Homec4science
Diffusion lammps (efficient_neuronet) Browse

lammps/doc/atom_modify.html
ae5beb2b307befficient_neuronet

Last Change
Raw File

atom_modify.html
View Options

<HTML>
<CENTER><A HREF = "http://lammps.sandia.gov">LAMMPS WWW Site</A> - <A HREF = "Manual.html">LAMMPS Documentation</A> - <A HREF = "Section_commands.html#comm">LAMMPS Commands</A>
</CENTER>
<HR>
<H3>atom_modify command
</H3>
<P><B>Syntax:</B>
</P>
<PRE>atom_modify keyword values ...
</PRE>
<UL><LI>one or more keyword/value pairs may be appended
<LI>keyword = <I>map</I> or <I>first</I> or <I>sort</I>
<PRE> <I>map</I> value = <I>array</I> or <I>hash</I>
<I>first</I> value = group-ID = group whose atoms will appear first in internal atom lists
<I>sort</I> values = Nfreq binsize
Nfreq = sort atoms spatially every this many time steps
binsize = bin size for spatial sorting (distance units)
</PRE>
</UL>
<P><B>Examples:</B>
</P>
<PRE>atom_modify map hash
atom_modify map array sort 10000 2.0
atom_modify first colloid
</PRE>
<P><B>Description:</B>
</P>
<P>Modify properties of the atom style selected within LAMMPS.
</P>
<P>The <I>map</I> keyword determines how atom ID lookup is done for molecular
problems. Lookups are performed by bond (angle, etc) routines in
LAMMPS to find the local atom index associated with a global atom ID.
When the <I>array</I> value is used, each processor stores a lookup table
of length N, where N is the total # of atoms in the system. This is
the fastest method for most simulations, but a processor can run out
of memory to store the table for very large simulations. The <I>hash</I>
value uses a hash table to perform the lookups. This method can be
slightly slower than the <I>array</I> method, but its memory cost is
proportional to N/P on each processor, where P is the total number of
processors running the simulation.
</P>
<P>The <I>first</I> keyword allows a <A HREF = "group.html">group</A> to be specified whose
atoms will be maintained as the first atoms in each processor's list
of owned atoms. This in only useful when the specified group is a
small fraction of all the atoms, and there are other operations LAMMPS
is performing that will be sped-up significantly by being able to loop
over the smaller set of atoms. Otherwise the reordering required by
this option will be a net slow-down. The <A HREF = "neigh_modify.html">neigh_modify
include</A> and <A HREF = "communicate.html">communicate group</A>
commands are two examples of commands that require this setting to
work efficiently. Several <A HREF = "fix.html">fixes</A>, most notably time
integration fixes like <A HREF = "fix_nve.html">fix nve</A>, also take advantage of
this setting if the group they operate on is the group specified by
this command. Note that specifying "all" as the group-ID effectively
turns off the <I>first</I> option.
</P>
<P>It is OK to use the <I>first</I> keyword with a group that has not yet been
defined, e.g. to use the atom_modify first command at the beginning of
your input script. LAMMPS does not use the group until a simullation
is run.
</P>
<P>The <I>sort</I> keyword turns on a spatial sorting or reordering of atoms
within each processor's sub-domain every <I>Nfreq</I> timesteps. This can
improve cache performance and thus speed-up a LAMMPS simulation, as
discussed in a paper by <A HREF = "#Meloni">(Meloni)</A>. Its efficacy depends on
the problem size (atoms/processor), how quickly the system becomes
disordered, and various other factors. As a general rule, sorting is
typically more effective at speeding up simulations of liquids as
opposed to solids. In tests we have done, the speed-up can range from
zero to 3-4x.
</P>
<P>Reordering is peformed every <I>Nfreq</I> timesteps during a dynamics run
or iterations during a minimization. More precisely, reordering
occurs at the first reneighboring that occurs after the target
timestep. The reordering is performed locally by each processor,
using bins of the specified <I>binsize</I>. If <I>binsize</I> is set to 0.0,
then a binsize equal to half the <A HREF = "neighbor.html">neighbor</A> cutoff
distance (force cutoff plus skin distance) is used, which is a
reasonable value. After the atoms have been binned, they are
reordered so that atoms in the same bin are adjacent to each other in
the processor's 1d list of atoms.
</P>
<P>The goal of this procedure is for atoms to put atoms close to each
other in the processor's one-dimensional list of atoms that are also
near to each other spatially. This can improve cache performance when
pairwise intereractions and neighbor lists are computed. Note that if
bins are too small, there will be few atoms/bin. Likewise if bins are
too large, there will be many atoms/bin. In both cases, the goal of
cache locality will be undermined.
</P>
<P>IMPORTANT NOTE: Running a simulation with sorting on versus off should
not change the simulation results in a statistical sense. However, a
different ordering will induce round-off differences, which will lead
to diverging trajectories over time when comparing two simluations.
Various commands, particularly those which use random numbers
(e.g. <A HREF = "velocity.html">velocity create</A>, and <A HREF = "fix_langevin.html">fix
langevin</A>), may generate (statistically identical)
results which depend on the order in which atoms are processed. The
order of atoms in a <A HREF = "dump.html">dump</A> file will also typically change
if sorting is enabled.
</P>
<P><B>Restrictions:</B>
</P>
<P>The map keyword can only be used before the simulation box is defined
by a <A HREF = "read_data.html">read_data</A> or <A HREF = "create_box.html">create_box</A>
command.
</P>
<P>The <I>first</I> and <I>sort</I> options cannot be used together. Since sorting
is on by default, it will be turned off if the <I>first</I> keyword is
used with a group-ID that is not "all".
</P>
<P><B>Related commands:</B> none
</P>
<P><B>Default:</B>
</P>
<P>By default, atomic (non-molecular) problems do not allocate maps. For
molecular problems, the option default is map = array. By default, a
"first" group is not defined. By default, sorting is enabled with a
frequency of 1000 and a binsize of 0.0, which means the neighbor
cutoff will be used to set the bin size.
</P>
<HR>
<A NAME = "Meloni"></A>
<P><B>(Meloni)</B> Meloni and Rasati, J Chem Phys, 126, 121102 (2007).
</P>
</HTML>
c4science · Help