Homec4science
Diffusion lammps (efficient_neuronet) Browse

lammps/doc/pair_sw.txt
5f445a166317efficient_neuronet

Last Change
Raw File

pair_sw.txt
View Options

"LAMMPS WWW Site"_lws - "LAMMPS Documentation"_ld - "LAMMPS Commands"_lc :c
:link(lws,http://lammps.sandia.gov)
:link(ld,Manual.html)
:link(lc,Section_commands.html#comm)
:line
pair_style sw command :h3
[Syntax:]
pair_style sw :pre
[Examples:]
pair_style sw
pair_coeff * * si.sw Si
pair_coeff * * SiC.sw Si C Si :pre
[Description:]
The {sw} style computes a 3-body "Stillinger-Weber"_#Stillinger
potential for the energy E of a system of atoms as
:c,image(Eqs/pair_sw.jpg)
where phi2 is a two-body term and phi3 is a three-body term. The
summations in the formula are over all neighbors J and K of atom I
within a cutoff distance = a*sigma.
Only a single pair_coeff command is used with the {sw} style which
specifies a Stillinger-Weber potential file with parameters for all
needed elements. These are mapped to LAMMPS atom types by specifying
N additional arguments after the filename in the pair_coeff command,
where N is the number of LAMMPS atom types:
filename
N element names = mapping of SW elements to atom types :ul
As an example, imagine the SiC.sw file has Stillinger-Weber values for
Si and C. If your LAMMPS simulation has 4 atoms types and you want
the 1st 3 to be Si, and the 4th to be C, you would use the following
pair_coeff command:
pair_coeff * * SiC.sw Si Si Si C :pre
The 1st 2 arguments must be * * so as to span all LAMMPS atom types.
The first three Si arguments map LAMMPS atom types 1,2,3 to the Si
element in the SW file. The final C argument maps LAMMPS atom type 4
to the C element in the SW file. If a mapping value is specified as
NULL, the mapping is not performed. This can be used when a {sw}
potential is used as part of the {hybrid} pair style. The NULL values
are placeholders for atom types that will be used with other
potentials.
Stillinger-Weber files in the {potentials} directory of the LAMMPS
distribution have a ".sw" suffix. Lines that are not blank or
comments (starting with #) define parameters for a triplet of
elements. The parameters in a single entry correspond to the two-body
and three-body coefficients in the formula above:
element 1 (the center atom in a 3-body interaction)
element 2
element 3
epsilon (energy units)
sigma (distance units)
a
lambda
gamma
costheta0
A
B
p
q :ul
The A, B, p, and q parameters are used only for two-body
interactions. The lambda, gamma, and costheta0 parameters are used only for
three-body interactions. The epsilon, sigma and a parameters are used
for both two-body and three-body interactions.
The non-annotated parameters are unitless.
The Stillinger-Weber potential file must contain entries for all the
elements listed in the pair_coeff command. It can also contain
entries for additional elements not being used in a particular
simulation; LAMMPS ignores those entries.
For a single-element simulation, only a single entry is required
(e.g. SiSiSi). For a two-element simulation, the file must contain 8
entries (for SiSiSi, SiSiC, SiCSi, SiCC, CSiSi, CSiC, CCSi, CCC), that
specify SW parameters for all permutations of the two elements
interacting in three-body configurations. Thus for 3 elements, 27
entries would be required, etc.
As annotated above, the first element in the entry is the center atom
in a three-body interaction. Thus an entry for SiCC means a Si atom
with 2 C atoms as neighbors. By symmetry, three-body parameters for
SiCSi and SiSiC entries should be the same. The parameters used for
the two-body interaction come from the entry where the 2nd element is
repeated. Thus the two-body parameters for Si interacting with C,
comes from the SiCC entry. Again by symmetry, the two-body parameters
in the SiCC and CSiSi entries should thus be the same. The parameters
used for a particular three-body interaction come from the entry with
the corresponding three elements. The parameters used only for
two-body interactions (A, B, p, and q) in entries whose 2nd and 3rd
element are different (e.g. SiCSi) are not used for anything and can
be set to 0.0 if desired.
:line
[Mixing, shift, table, tail correction, per-atom energy/stress,
restart, rRESPA info]:
For atom type pairs I,J and I != J, where types I and J correspond to
two different element types, mixing is performed by LAMMPS as
described above from values in the potential file.
This pair style does not support the "pair_modify"_pair_modify.html
shift, table, and tail options.
This pair style does not calculate per-atom energy and stress, as used
by the "compute epair/atom"_compute_epair_atom.html, "compute
stress/atom"_compute_stress_atom.html, and "dump custom"_dump.html
commands.
This pair style does not write its information to "binary restart
files"_restart.html, since it is stored in potential files. Thus, you
need to re-specify the pair_style and pair_coeff commands in an input
script that reads a restart file.
This pair style can only be used via the {pair} keyword of the
"run_style respa"_run_style.html command. It does not support the
{inner}, {middle}, {outer} keywords.
:line
[Restrictions:]
This pair style is part of the "manybody" package. It is only enabled
if LAMMPS was built with that package (which it is by default). See
the "Making LAMMPS"_Section_start.html#2_3 section for more info.
This pair style requires the "newton"_newton.html setting to be "on"
for pair interactions.
The Stillinger-Weber potential files provided with LAMMPS (see the
potentials directory) are parameterized for metal "units"_units.html.
You can use the SW potential with any LAMMPS units, but you would need
to create your own SW potential file with coefficients listed in the
appropriate units if your simulation doesn't use "metal" units.
[Related commands:]
"pair_coeff"_pair_coeff.html
[Default:] none
:line
:link(Stillinger)
[(Stillinger)] Stillinger and Weber, Phys Rev B, 31, 5262 (1985).
c4science · Help