template-ID = ID of molecule template specified in a separate <aclass="reference internal"href="molecule.html"><spanclass="doc">molecule</span></a> command
<em>shake</em> value = fix-ID
fix-ID = ID of <aclass="reference internal"href="fix_shake.html"><spanclass="doc">fix shake</span></a> command
<em>region</em> value = region-ID
region-ID = ID of region where MC moves are allowed
<em>maxangle</em> value = maximum molecular rotation angle (degrees)
<em>pressure</em> value = pressure of the gas reservoir (pressure units)
<em>fugacity_coeff</em> value = fugacity coefficient of the gas reservoir (unitless)
<em>full_energy</em> = compute the entire system energy when performing MC moves
<em>charge</em> value = charge of inserted atoms (charge units)
<em>group</em> value = group-ID
group-ID = group-ID for inserted atoms (string)
<em>grouptype</em> values = type group-ID
type = atom type (int)
group-ID = group-ID for inserted atoms (string)
<em>intra_energy</em> value = intramolecular energy (energy units)
<em>tfac_insert</em> value = scale up/down temperature of inserted atoms (unitless)
fix 4 my_gas gcmc 1 10 10 1 123456543 300.0 -12.5 1.0 region disk
</pre>
</div>
<divclass="section"id="description">
<h2>Description</h2>
<p>This fix performs grand canonical Monte Carlo (GCMC) exchanges of
atoms or molecules of the given type with an imaginary ideal gas reservoir at
the specified T and chemical potential (mu) as discussed in
<aclass="reference internal"href="fix_ti_spring.html#frenkel"><spanclass="std std-ref">(Frenkel)</span></a>. If used with the <aclass="reference internal"href="fix_nh.html"><spanclass="doc">fix nvt</span></a> command,
simulations in the grand canonical ensemble (muVT, constant chemical
potential, constant volume, and constant temperature) can be
performed. Specific uses include computing isotherms in microporous
materials, or computing vapor-liquid coexistence curves.</p>
<p>Every N timesteps the fix attempts a number of GCMC exchanges (insertions
or deletions) of gas atoms or molecules of
the given type between the simulation cell and the imaginary
reservoir. It also attempts a number of Monte Carlo
moves (translations and molecule rotations) of gas of the given type
within the simulation cell or region. The average number of
attempted GCMC exchanges is X. The average number of attempted MC moves is M.
M should typically be chosen to be
approximately equal to the expected number of gas atoms or molecules
of the given type within the simulation cell or region,
which will result in roughly one
MC translation per atom or molecule per MC cycle.</p>
<p>For MC moves of molecular gasses, rotations and translations are each
attempted with 50% probability. For MC moves of atomic gasses,
translations are attempted 100% of the time. For MC exchanges of
either molecular or atomic gasses, deletions and insertions are each
attempted with 50% probability.</p>
<p>All inserted particles are always assigned to two groups: the default group
“all” and the group specified in the fix gcmc command (which can also
be “all”). In addition, particles are also added to any groups specified
by the <em>group</em> and <em>grouptype</em> keywords.
If inserted particles are individual atoms, they are
assigned the atom type given by the type argument. If they are molecules,
the type argument has no effect and must be set to zero. Instead,
the type of each atom in the inserted molecule is specified
in the file read by the <aclass="reference internal"href="molecule.html"><spanclass="doc">molecule</span></a> command.</p>
<p>This fix cannot be used to perform MC insertions of gas atoms or
molecules other than the exchanged type, but MC deletions,
translations, and rotations can be performed on any atom/molecule in
the fix group. All atoms in the simulation cell can be moved using
regular time integration translations, e.g. via
<aclass="reference internal"href="fix_nh.html"><spanclass="doc">fix nvt</span></a>, resulting in a hybrid GCMC+MD simulation. A
smaller-than-usual timestep size may be needed when running such a
hybrid simulation, especially if the inserted molecules are not well
equilibrated.</p>
<p>This command may optionally use the <em>region</em> keyword to define an
exchange and move volume. The specified region must have been
previously defined with a <aclass="reference internal"href="region.html"><spanclass="doc">region</span></a> command. It must be
defined with side = <em>in</em>. Insertion attempts occur only within the
specified region. For non-rectangular regions, random trial
points are generated within the rectangular bounding box until a point is found
that lies inside the region. If no valid point is generated after 1000 trials,
no insertion is performed, but it is counted as an attempted insertion.
Move and deletion attempt candidates are selected
from gas atoms or molecules within the region. If there are no candidates,
no move or deletion is performed, but it is counted as an attempt move
or deletion. If an attempted move places the atom or molecule center-of-mass outside
the specified region, a new attempted move is generated. This process is repeated
until the atom or molecule center-of-mass is inside the specified region.</p>
<p>If used with <aclass="reference internal"href="fix_nh.html"><spanclass="doc">fix nvt</span></a>, the temperature of the imaginary
reservoir, T, should be set to be equivalent to the target temperature
used in fix nvt. Otherwise, the imaginary reservoir
will not be in thermal equilibrium with the simulation cell. Also,
it is important that the temperature used by fix nvt be dynamic,
which can be achieved as follows:</p>
<preclass="literal-block">
compute mdtemp mdatoms temp
compute_modify mdtemp dynamic yes
fix mdnvt mdatoms nvt temp 300.0 300.0 10.0
fix_modify mdnvt temp mdtemp
</pre>
<p>Note that neighbor lists are re-built every timestep that this fix is
invoked, so you should not set N to be too small. However, periodic
rebuilds are necessary in order to avoid dangerous rebuilds and missed
interactions. Specifically, avoid performing so many MC translations
per timestep that atoms can move beyond the neighbor list skin
distance. See the <aclass="reference internal"href="neighbor.html"><spanclass="doc">neighbor</span></a> command for details.</p>
<p>When an atom or molecule is to be inserted, its
coordinates are chosen at a random position within the current
simulation cell or region, and new atom velocities are randomly chosen from
the specified temperature distribution given by T. The effective
temperature for new atom velocities can be increased or decreased
using the optional keyword <em>tfac_insert</em> (see below). Relative
coordinates for atoms in a molecule are taken from the template
molecule provided by the user. The center of mass of the molecule
is placed at the insertion point. The orientation of the molecule
is chosen at random by rotating about this point.</p>
<p>Individual atoms are inserted, unless the <em>mol</em> keyword is used. It
specifies a <em>template-ID</em> previously defined using the
<aclass="reference internal"href="molecule.html"><spanclass="doc">molecule</span></a> command, which reads a file that defines the
molecule. The coordinates, atom types, charges, etc, as well as any
bond/angle/etc and special neighbor information for the molecule can
be specified in the molecule file. See the <aclass="reference internal"href="molecule.html"><spanclass="doc">molecule</span></a>
command for details. The only settings required to be in this file
are the coordinates and types of atoms in the molecule.</p>
<p>When not using the <em>mol</em> keyword, you should ensure you do not delete
atoms that are bonded to other atoms, or LAMMPS will
soon generate an error when it tries to find bonded neighbors. LAMMPS will
warn you if any of the atoms eligible for deletion have a non-zero
molecule ID, but does not check for this at the time of deletion.</p>
<p>If you wish to insert molecules via the <em>mol</em> keyword, that will have
their bonds or angles constrained via SHAKE, use the <em>shake</em> keyword,
specifying as its value the ID of a separate <aclass="reference internal"href="fix_shake.html"><spanclass="doc">fix shake</span></a> command which also appears in your input script.</p>
<p>Optionally, users may specify the maximum rotation angle for
molecular rotations using the <em>maxangle</em> keyword and specifying
the angle in degrees. Rotations are performed by generating a random
point on the unit sphere and a random rotation angle on the
range [0,maxangle). The molecule is then rotated by that angle about an
axis passing through the molecule center of mass. The axis is parallel
to the unit vector defined by the point on the unit sphere.
The same procedure is used for randomly rotating molecules when they
are inserted, except that the maximum angle is 360 degrees.</p>
<p>Note that fix GCMC does not use configurational bias
MC or any other kind of sampling of intramolecular degrees of freedom.
Inserted molecules can have different orientations, but they will all
have the same intramolecular configuration,
which was specified in the molecule command input.</p>
<p>For atomic gasses, inserted atoms have the specified atom type, but
deleted atoms are any atoms that have been inserted or that belong
to the user-specified fix group. For molecular gasses, exchanged
molecules use the same atom types as in the template molecule
supplied by the user. In both cases, exchanged
atoms/molecules are assigned to two groups: the default group “all”
and the group specified in the fix gcmc command (which can also be
“all”).</p>
<p>The gas reservoir pressure can be specified using the <em>pressure</em>
keyword, in which case the user-specified chemical potential is
ignored. For non-ideal gas reservoirs, the user may also specify the
fugacity coefficient using the <em>fugacity_coeff</em> keyword.</p>
<p>The <em>full_energy</em> option means that fix GCMC will compute the total
potential energy of the entire simulated system. The total system
energy before and after the proposed GCMC move is then used in the
Metropolis criterion to determine whether or not to accept the
proposed GCMC move. By default, this option is off, in which case
only partial energies are computed to determine the difference in
energy that would be caused by the proposed GCMC move.</p>
<p>The <em>full_energy</em> option is needed for systems with complicated
potential energy calculations, including the following:</p>
<ulclass="simple">
<li>long-range electrostatics (kspace)</li>
<li>many-body pair styles</li>
<li>hybrid pair styles</li>
<li>eam pair styles</li>
<li>triclinic systems</li>
<li>need to include potential energy contributions from other fixes</li>
</ul>
<p>In these cases, LAMMPS will automatically apply the <em>full_energy</em>
keyword and issue a warning message.</p>
<p>When the <em>mol</em> keyword is used, the <em>full_energy</em> option also includes
the intramolecular energy of inserted and deleted molecules. If this
is not desired, the <em>intra_energy</em> keyword can be used to define an
amount of energy that is subtracted from the final energy when a molecule
is inserted, and added to the initial energy when a molecule is
deleted. For molecules that have a non-zero intramolecular energy, this
will ensure roughly the same behavior whether or not the <em>full_energy</em>
option is used.</p>
<p>Inserted atoms and molecules are assigned random velocities based on the
specified temperature T. Because the relative velocity of
all atoms in the molecule is zero, this may result in inserted molecules
that are systematically too cold. In addition, the intramolecular potential
energy of the inserted molecule may cause the kinetic energy
of the molecule to quickly increase or decrease after insertion.
The <em>tfac_insert</em> keyword allows the user to counteract these effects
by changing the temperature used to assign velocities to
inserted atoms and molecules by a constant factor. For a
particular application, some experimentation may be required
to find a value of <em>tfac_insert</em> that results in inserted molecules that
equilibrate quickly to the correct temperature.</p>
<p>Some fixes have an associated potential energy. Examples of such fixes
<p>The <em>group</em> keyword assigns all inserted atoms to the <aclass="reference internal"href="group.html"><spanclass="doc">group</span></a>
of the group-ID value. The <em>grouptype</em> keyword assigns all
inserted atoms of the specified type to the <aclass="reference internal"href="group.html"><spanclass="doc">group</span></a>
of the group-ID value.</p>
<p><strong>Restart, fix_modify, output, run start/stop, minimize info:</strong></p>
<p>This fix writes the state of the fix to <aclass="reference internal"href="restart.html"><spanclass="doc">binary restart files</span></a>. This includes information about the random
number generator seed, the next timestep for MC exchanges, etc. See
the <aclass="reference internal"href="read_restart.html"><spanclass="doc">read_restart</span></a> command for info on how to
re-specify a fix in an input script that reads a restart file, so that
the operation of the fix continues in an uninterrupted fashion.</p>
<p>None of the <aclass="reference internal"href="fix_modify.html"><spanclass="doc">fix_modify</span></a> options are relevant to this
fix.</p>
<p>This fix computes a global vector of length 8, which can be accessed
by various <aclass="reference internal"href="Section_howto.html#howto-15"><spanclass="std std-ref">output commands</span></a>. The vector
values are the following global cumulative quantities:</p>
<ulclass="simple">
<li>1 = translation attempts</li>
<li>2 = translation successes</li>
<li>3 = insertion attempts</li>
<li>4 = insertion successes</li>
<li>5 = deletion attempts</li>
<li>6 = deletion successes</li>
<li>7 = rotation attempts</li>
<li>8 = rotation successes</li>
</ul>
<p>The vector values calculated by this fix are “extensive”.</p>
<p>No parameter of this fix can be used with the <em>start/stop</em> keywords of
the <aclass="reference internal"href="run.html"><spanclass="doc">run</span></a> command. This fix is not invoked during <aclass="reference internal"href="minimize.html"><spanclass="doc">energy minimization</span></a>.</p>
</div>
<divclass="section"id="restrictions">
<h2>Restrictions</h2>
<p>This fix is part of the MC package. It is only enabled if LAMMPS was
built with that package. See the <aclass="reference internal"href="Section_start.html#start-3"><spanclass="std std-ref">Making LAMMPS</span></a> section for more info.</p>
<p>Do not set “neigh_modify once yes” or else this fix will never be
called. Reneighboring is required.</p>
<p>Can be run in parallel, but aspects of the GCMC part will not scale
well in parallel. Only usable for 3D simulations.</p>
<p>Note that very lengthy simulations involving insertions/deletions of
billions of gas molecules may run out of atom or molecule IDs and
trigger an error, so it is better to run multiple shorter-duration
simulations. Likewise, very large molecules have not been tested
and may turn out to be problematic.</p>
<p>Use of multiple fix gcmc commands in the same input script can be
problematic if using a template molecule. The issue is that the
user-referenced template molecule in the second fix gcmc command
may no longer exist since it might have been deleted by the first
fix gcmc command. An existing template molecule will need to be
referenced by the user for each subsequent fix gcmc command.</p>
<p>Because molecule insertion does not work in combination with
fix rigid, simulataneous use of fix rigid or fix rigid/small
Built with <ahref="http://sphinx-doc.org/">Sphinx</a> using a <ahref="https://github.com/snide/sphinx_rtd_theme">theme</a> provided by <ahref="https://readthedocs.org">Read the Docs</a>.