Homec4science
Diffusion lammps (master) Browse

lammps/doc/fix_temp_berendsen.html
bdd81705ccd2master

Last Change
Raw File

fix_temp_berendsen.html
View Options

<HTML>
<CENTER><A HREF = "http://lammps.sandia.gov">LAMMPS WWW Site</A> - <A HREF = "Manual.html">LAMMPS Documentation</A> - <A HREF = "Section_commands.html#comm">LAMMPS Commands</A>
</CENTER>
<HR>
<H3>fix temp/berendsen command
</H3>
<H3>fix temp/berendsen/cuda command
</H3>
<P><B>Syntax:</B>
</P>
<PRE>fix ID group-ID temp/berendsen Tstart Tstop Tdamp
</PRE>
<UL><LI>ID, group-ID are documented in <A HREF = "fix.html">fix</A> command
<LI>temp/berendsen = style name of this fix command
<LI>Tstart,Tstop = desired temperature at start/end of run
<PRE> Tstart can be a variable (see below)
</PRE>
<LI>Tdamp = temperature damping parameter (time units)
</UL>
<P><B>Examples:</B>
</P>
<PRE>fix 1 all temp/berendsen 300.0 300.0 100.0
</PRE>
<P><B>Description:</B>
</P>
<P>Reset the temperature of a group of atoms by using a Berendsen
thermostat <A HREF = "#Berendsen">(Berendsen)</A>, which rescales their velocities
every timestep.
</P>
<P>The thermostat is applied to only the translational degrees of freedom
for the particles, which is an important consideration for finite-size
particles which have rotational degrees of freedom are being
thermostatted with this fix. The translational degrees of freedom can
also have a bias velocity removed from them before thermostatting
takes place; see the description below.
</P>
<P>The desired temperature at each timestep is a ramped value during the
run from <I>Tstart</I> to <I>Tstop</I>. The <I>Tdamp</I> parameter is specified in
time units and determines how rapidly the temperature is relaxed. For
example, a value of 100.0 means to relax the temperature in a timespan
of (roughly) 100 time units (tau or fmsec or psec - see the
<A HREF = "units.html">units</A> command).
</P>
<P><I>Tstart</I> can be specified as an equal-style <A HREF = "variable.html">variable</A>.
In this case, the <I>Tstop</I> setting is ignored. If the value is a
variable, it should be specified as v_name, where name is the variable
name. In this case, the variable will be evaluated each timestep, and
its value used to determine the target temperature.
</P>
<P>Equal-style variables can specify formulas with various mathematical
functions, and include <A HREF = "thermo_style.html">thermo_style</A> command
keywords for the simulation box parameters and timestep and elapsed
time. Thus it is easy to specify a time-dependent temperature.
</P>
<P>IMPORTANT NOTE: Unlike the <A HREF = "fix_nh.html">fix nvt</A> command which
performs Nose/Hoover thermostatting AND time integration, this fix
does NOT perform time integration. It only modifies velocities to
effect thermostatting. Thus you must use a separate time integration
fix, like <A HREF = "fix_nve.html">fix nve</A> to actually update the positions of
atoms using the modified velocities. Likewise, this fix should not
normally be used on atoms that also have their temperature controlled
by another fix - e.g. by <A HREF = "fix_nh.html">fix nvt</A> or <A HREF = "fix_langevin.html">fix
langevin</A> commands.
</P>
<P>See <A HREF = "Section_howto.html#howto_16">this howto section</A> of the manual for
a discussion of different ways to compute temperature and perform
thermostatting.
</P>
<P>This fix computes a temperature each timestep. To do this, the fix
creates its own compute of style "temp", as if this command had been
issued:
</P>
<PRE>compute fix-ID_temp group-ID temp
</PRE>
<P>See the <A HREF = "compute_temp.html">compute temp</A> command for details. Note
that the ID of the new compute is the fix-ID + underscore + "temp",
and the group for the new compute is the same as the fix group.
</P>
<P>Note that this is NOT the compute used by thermodynamic output (see
the <A HREF = "thermo_style.html">thermo_style</A> command) with ID = <I>thermo_temp</I>.
This means you can change the attributes of this fix's temperature
(e.g. its degrees-of-freedom) via the
<A HREF = "compute_modify.html">compute_modify</A> command or print this temperature
during thermodynamic output via the <A HREF = "thermo_style.html">thermo_style
custom</A> command using the appropriate compute-ID.
It also means that changing attributes of <I>thermo_temp</I> will have no
effect on this fix.
</P>
<P>Like other fixes that perform thermostatting, this fix can be used
with <A HREF = "compute.html">compute commands</A> that calculate a temperature
after removing a "bias" from the atom velocities. E.g. removing the
center-of-mass velocity from a group of atoms or only calculating
temperature on the x-component of velocity or only calculating
temperature for atoms in a geometric region. This is not done by
default, but only if the <A HREF = "fix_modify.html">fix_modify</A> command is used
to assign a temperature compute to this fix that includes such a bias
term. See the doc pages for individual <A HREF = "compute.html">compute
commands</A> to determine which ones include a bias. In
this case, the thermostat works in the following manner: the current
temperature is calculated taking the bias into account, bias is
removed from each atom, thermostatting is performed on the remaining
thermal degrees of freedom, and the bias is added back in.
</P>
<HR>
<P>Styles with a <I>cuda</I> suffix are functionally the same as the
corresponding style without the suffix. They have been optimized to
run faster, depending on your available hardware, as discussed in
<A HREF = "Section_accelerate.html">Section_accelerate</A> of the manual. The
accelerated styles take the same arguments and should produce the same
results, except for round-off and precision issues.
</P>
<P>These accelerated styles are part of the USER-CUDA package. They are
only enabled if LAMMPS was built with that package. See the <A HREF = "Section_start.html#start_3">Making
LAMMPS</A> section for more info.
</P>
<P>You can specify the accelerated styles explicitly in your input script
by including their suffix, or you can use the <A HREF = "Section_start.html#start_7">-suffix command-line
switch</A> when you invoke LAMMPS, or you can
use the <A HREF = "suffix.html">suffix</A> command in your input script.
</P>
<P>See <A HREF = "Section_accelerate.html">Section_accelerate</A> of the manual for
more instructions on how to use the accelerated styles effectively.
</P>
<HR>
<P><B>Restart, fix_modify, output, run start/stop, minimize info:</B>
</P>
<P>No information about this fix is written to <A HREF = "restart.html">binary restart
files</A>.
</P>
<P>The <A HREF = "fix_modify.html">fix_modify</A> <I>temp</I> option is supported by this
fix. You can use it to assign a temperature <A HREF = "compute.html">compute</A>
you have defined to this fix which will be used in its thermostatting
procedure, as described above. For consistency, the group used by
this fix and by the compute should be the same.
</P>
<P>The <A HREF = "fix_modify.html">fix_modify</A> <I>energy</I> option is supported by this
fix to add the energy change implied by a velocity rescaling to the
system's potential energy as part of <A HREF = "thermo_style.html">thermodynamic
output</A>.
</P>
<P>This fix computes a global scalar which can be accessed by various
<A HREF = "Section_howto.html#howto_15">output commands</A>. The scalar is the
cummulative energy change due to this fix. The scalar value
calculated by this fix is "extensive".
</P>
<P>This fix can ramp its target temperature over multiple runs, using the
<I>start</I> and <I>stop</I> keywords of the <A HREF = "run.html">run</A> command. See the
<A HREF = "run.html">run</A> command for details of how to do this.
</P>
<P>This fix is not invoked during <A HREF = "minimize.html">energy minimization</A>.
</P>
<P><B>Restrictions:</B> none
</P>
<P><B>Related commands:</B>
</P>
<P><A HREF = "fix_nve.html">fix nve</A>, <A HREF = "fix_nh.html">fix nvt</A>, <A HREF = "fix_temp_rescale.html">fix
temp/rescale</A>, <A HREF = "fix_langevin.html">fix langevin</A>,
<A HREF = "fix_modify.html">fix_modify</A>, <A HREF = "compute_temp.html">compute temp</A>,
<A HREF = "fix_press_berendsen.html">fix press/berendsen</A>
</P>
<P><B>Default:</B> none
</P>
<HR>
<A NAME = "Berendsen"></A>
<P><B>(Berendsen)</B> Berendsen, Postma, van Gunsteren, DiNola, Haak, J Chem
Phys, 81, 3684 (1984).
</P>
</HTML>
c4science · Help